Oil & Gas Glossary 1.0

A pipe attached to the blowout preventer stack out of which kick fluids and mud can be pumped to the choke manifold when a blowout preventer is closed in on a kick.

A method of killing a well that has kicked, in which the choke size is adjusted to maintain a constant casing pressure. This method does not work unless the kick is all or nearly all salt water. if the kick is gas, this method will not maintain a constant bottomhole pressure, because gas expands as it rises in the annulus. In any case, it is not a recommended well-control procedure.

An intrusion of formation fluids into the borehole, i.e., a kick.

A device that removes gas from the mud coming out of a well when a kick is being circulated out.

3. trying to pump out a gas influx before the expansion of gas reduces pressure allowing the well to kick.

1. the process of raising the drill stem out of the wellbore when the well is shut in on a kick.

A sudden increase in the drill bit's rate of penetration. it sometimes indicates that the bit has penetrated a high-pressure zone and thus warns of the possibility of a kick.

The pressure at which a well that has been closed in on a kick is circulated when well-killing procedures are begun

A device used to direct fluid flowing from a well away from the drilling rig. When a kick is encountered at shallow depths, the well often cannot be shut in safely; therefore, a diverter is used to allow the well to flow through a side outlet (a diverter line).

2. a valve installed at the top of the drill stem to prevent flow out of the drill pipe if a kick occurs during tripping operations.

1. the process of lowering the drill stem into the wellbore when the well is shut in on a kick and when the weight of the drill stem is sufficient to overcome the force of well pressure.

A method of determining the amount of pressure that is allowed to appear on the casing pressure gauge as a kick is circulated out of a well. In general, it is determined by slowly pumping mud into the well while it is shut in and observing the pressure at which the formation begins to take mud.

A device that continually measures and may record the flow rate of mud returning from the annulus and flowing out of the mud return line. If the mud does not flow at a fairly constant rate, a kick or lost circulation may have occurred.

2. to dose the blowout preventers on a well to control a kick. The blowout preventers close off the annulus so that pressure from below cannot flow to the surface.

A drilling mud that contains entrained formation gas, giving the mud a characteristically fluffy texture. Then entrained gas in not released before the fluid returns to the well, the weight or density of the fluid column is reduced. Because a large amount of gas in mud lowers its density, gas-cut mud must be treated to reduce the chance of a kick.

A set of controls, usually placed on the rig floor, that is manipulated to control the amount of drilling fluid being circulated through the choke manifold. This procedure is necessary when a kick is being circulated out of a well. See choke manifold.

The amount of pressure that, when applied inside a string of casing, causes the wall of the casing to fail. This pressure is critically important when a gas kick is being circulated out, because gas on the way to the surface expands and exerts more pressure than it exerted at the bottom of the well.

An entry of water, gas, oil, or other formation fluid into the wellbore during drilling. It occurs because the pressure exerted by the column of drilling fluid is not great enough to overcome the pressure exerted by the fluids in the formation drilled. If

A procedure whereby the formation immediately below the casing shoe is subjected to a pressure equal to the pressure expected to be exerted later by a higher drilling glut density or by the sum of a higher drilling fluid density and back-pressure created by a kick.

To pump drilling fluid into the wellbore while the pipe is being withdrawn to ensure that the wellbore remains full of fluid even though the pipe is withdrawn. Filling the hole lessens the danger of a kick or of caving of the well or the wellbore.

One of a series of devices that continuously monitor the level of the drilling mud in the mud tanks. The indicator usually consists of float devices in the mud tanks that sense the mud level and transmit data to a recording and alarm device (a pit-volume recorder) mounted near the driller's position on the rig floor. If the mud level drops too low or rises too high, the alarm sounds to warn the driller of losing circulation or a kick.

A special valve installed below the kelly. Usually, the valve is open so that drilling fluid can flow out of the kelly and down the drill stem. It can, however, be manually closed with a special wrench when necessary. In one case, the valve is closed and broken out, still attached to the kelly to prevent drilling mud in the kelly from draining onto the rig floor. In another case, when kick pressure inside the drill stem exists, the drill stem safety valve is close to prevent the pressure from escaping up the drill stem.