Oil & Gas Glossary 1.0

A diagnostic tool used to ascertain the position of a gas leak in the tubing of a gas-lift well.

A diagnostic tool used to ascertain the position of a gas leak in the tubing of a gas lift well.

A diagnostic tool used to ascertain the position of a gas leak in the tubing of a gas-lift well.

2. in wireline, trying to pull out of the well faster than the wireline tools are being blown upwards by unexpected pressure.

Preventers installed on top of the well or drill string as a precautionary measure while running wirelines. The preventer packing will close around the wireline.

A flared-end sub run on the end of the tubing string to permit easy access of wireline tools into the tubing ID.

A flared-end sub run on the end of the tubing string to permit easy access of wireline tools into the tubing ID.

A bottomhole choke run on wireline and landed in a nipple profile in the tubing string.

A small-diameter metal line used in wireline operations. Also called slick line. Compare conductor line.

A manually operated ram preventer especially adapted for closure around a wireline.

A manually operated ram preventer especially adapted for closure around a wireline.

A cable composed of steel wires twisted around a central core of fiber or steel wire to create a rope of great strength and considerable flexibility. Wire rope is used as drilling line (in rotary and cable-tool rigs), coring line, servicing line, winch line, and so on. It is often called cable or wireline; however, wireline is a single, slender metal rod, usually very flexible. Compare wireline.

A small-diameter conductive line used in electric wireline operations, such as electric well logging and perforating, in which the transmission of electrical current is required. Compare wireline.

A pulley that is normally attached to the wellhead at a convenient place for the wireline to pass through as it comes from the stuffing box sheave before being spooled onto the wireline reel. The hay pulley prevents any lateral force from being exerted on the lubricator and the wellhead.

A formation fluid sampling device, actually run on conductor line rather than wireline, that also logs flow and shut-in pressure in rock near the borehole. A spring mechanism holds a pad firmly against the sidewall while a piston creates a vacuum in a test chamber. Formation fluids enter the tes5t chamber through a valve in the pad. A recorder logs the rate at which the test chamber is filled. Fluids may also be drawn to fill a sampling chamber. Wireline formation tests may be done any number of times during one tip in the hole, so they are very useful in formation testing.

A diagnostic tool used to ascertain whether there is a gas leak in the tubing of a gas lift well. If there is a tubing leak, the pressure on the annulus will equal the pressure on the tubing.

A portable mast that an be erected as a unit, usually by a tackle that hoists the wireline or by hydraulic pistons. The upper section of a telescoping derrick is generally nested (telescoped) inside the lower section of the structure and raised to full height either by the wireline or by a hydraulic system.

A general term often used to refer to any type of log being run in a well. See log.

A general term often used to refer to any type of log being run in a well.

A device to connect the wireline to the tool string.

2. to force a wireline tool or tubing down the hole by using a reciprocating motion.

To fire a wireline-operated downhole tool from inside the service truck.

N. 1. a piece of cloth, rope or nylon strand used to mark the wireline when swabbing or bailing.

The wireline attached to ground anchors to provide lateral support for a mast or derrick.

A ported, extended production tub used as an alternative path for wireline measuring devices.

Abbreviation: a generic term for pressure setting assembly; a tool that is used to set permanent tools on electric wireline, through explosive force.

2. in swabbing or bailing, to attach a piece of cloth to the wireline to enable the operator to estimate the position of the swab or bailer in the well.

A wireline attached to a mast, derrick, or offshore platform to stabilize it. See wind guy line.

A tool used to gauge and clean junk and debris from the casing in conjunction with a junk catcher.

A valve in the bottom of a retainer. See wireline.

2. to lower or raise tools in or out of a well with pressure inside the well. The term comes from the fact that a lubricant (grease) is often used to provide a seal against well pressure while allowing wireline to move in or out of the well.

A device used to measure the depth of a well or the depth at a specific point in a well (such as to the top of a liner or to a fish) by counting the turns of a calibrated wheel rolling on a wireline as it is lowered into or pulled out of the well.

2. to lower or raise tools in or out of a well with pressure inside the well. The term comes from the fact that a lubricant (grease) is often used to provide a seal against well pressure while allowing wireline to move in or out of the well.

A poppet spring-loaded subsurface valve run in on wireline, landed in a profile, to shut the well if injection ceases.

Descriptive of any tool or device that can be pumped down a wellbore. Pump-down tools are not lowered into the well on wireline; instead, they are pumped down the well with the drilling fluid.

A wireline used on drilling rigs and well servicing rigs to operate a swab or bailer, to retrieve cores or to run logging devices. It is usually 9/16 of an inch (15 millimeters) in diameter and several thousand feet or meters long

A cylindrical or spherical device that is affixed to the end of a wireline just above the hook to keep the line straight and to provide weight. v: to soak metal pieces in a chemical solution to remove dirt and scale from the metal's surface.

A heavy weight or bar placed on or near a lightweight wireline tool. The bar provides weight so that the tool will lower properly into the well.

A wireline pressure setting tool for setting permanent downhole tools.

Specialized tools used to run equipment in a well, such as a wireline running tool for installing retrievable gas lift valves. Various tubing-type running tools are also used.

A special device placed in a string of tubing that can be operated by a wireline tool to open or close orifices to permit circulation between the tubing and the annulus. It may also be used to open or shut off production from various intervals in a well. Also called circulation sleeve.

V: 1. to operate a swab on a wireline to bring well fluids to the surface when the w4ell does not flow naturally. Swabbing is a temporary operation to determine whether the well can be made to flow. If the well does not flow after being swabbed, a pump is installed a a permanent lifting device to bring the oil to the surface.

A workover performed with a continuous steel tube, normally 3/4 inch to 1 inch outside diameter, which is run into the well in one piece inside the normal tubing. Lengths of the tubing up to 16,000 feet are stored on the surface on a reel in a manner similar to that used for wireline. The unit is rigged up over the wellhead. The tubing is injected through a control head that seals off the tubing and makes a pressure-tight connection. A unique feature of the unit is that it allows continuous circulation while it is being lowered into the hole.

A device run on wireline into the wellbore and inside the fishing string and fish to locate the area where a fish is stuck. When the drill string is pulled and turned, the electromagnetic fields of free pipe and stuck pipe differ. The free-point indicator is able to distinguish these differences, which are registered on a metering device at the surface.

A device that prevents leakage along a piston, rod, propeller shaft, or other moving part that passes through a hole in a cylinder or vessel. It consists of a box or chamber made by enlarging the hole and a gland containing compressed packing. On a well being artificially lifted by means of a sucker rod pump, the polished rod operates through a stuffing box, preventing escape of oil and diverting it into a side outlet to which is connected the flow line leading to the oil and gas separator or to the field storage tank. For a bottomhole pressure test, the wireline goes through a stuffing box and lubricator, allowing the gauge to be raised and lowered against well pressure. The lubricator provides a pressure-tight grease seal in the stuffing box.

1. to force pipe or tools into a high-pressure well that has not been killed (i.e., to run pipe or tools into the well against pressure when the weight of pipe is not great enough to force the pipe through the BOPs). Snubbing usually requires an array of wireline bocks and wire rope that forces the pipe or tools into the well through a stripper head or blowout preventer until the weight of the string is sufficient to overcome the lifting effect of the well pressure on the pipe in the preventer. In workover operations, snubbing is usually accomplished by using hydraulic power to force the pipe through the stripping head or blowout preventer.