Oil & Gas Glossary 1.0

A blowout preventer that uses rams to seal off pressure on a hole that is with or without pipe. Also called a ram preventer.

The closing and sealing components of a preventer, like the gate in a gate valve.

The assembly of pumps, valves, lines, accumulators, and other items necessary to open and close the blowout preventer equipment. Also called closing unit.

A blowout preventer placed on the seafloor for use by a floating offshore drilling rig.

Controls, usually located near the driller's position on the rig floor, that are manipulated to open and close the blowout preventers. See blowout preventer.

A blowout preventer that uses shear rams as closing elements.

A manually operated ram preventer especially adapted for closure around a wireline.

A manually operated ram preventer especially adapted for closure around a wireline.

A preventer having a unit of packing material whose closure depends on well pressure coming from below. It is used primarily to strip pipe through the hole or allow pipe to be moved with pressure on the annulus.

A sealing component for a blowout preventer that closes the annular space between the pipe and the blowout preventer or wellhead.

1. a vertical arrangement of blowout prevention equipment. Also called preventer stack. See blowout preventer.

See ram blowout preventer.

A blowout preventer that uses pipe rams as the closing elements. See pipe ram.

A device placed or hung in the casing below the blowout preventer stack to form a pressure tight seal. Pressure is then applied to the blowout preventer stack to test it for leaks

Any valve installed in the drill stem to prevent a blowout through the stem. Mud can be pumped in but flow back up the stem is prevented. Also called an internal blowout preventer.

A pipe attached to the blowout preventer stack out of which kick fluids and mud can be pumped to the choke manifold when a blowout preventer is closed in on a kick.

1. to force pipe or tools into a high-pressure well that has not been killed (i.e., to run pipe or tools into the well against pressure when the weight of pipe is not great enough to force the pipe through the BOPs). Snubbing usually requires an array of wireline bocks and wire rope that forces the pipe or tools into the well through a stripper head or blowout preventer until the weight of the string is sufficient to overcome the lifting effect of the well pressure on the pipe in the preventer. In workover operations, snubbing is usually accomplished by using hydraulic power to force the pipe through the stripping head or blowout preventer.

A device that stores hydraulic fluid under pressure in special containers and provides a method to open and close the blowout preventers quickly and reliably. Usually, compressed air and hydraulic pressure provide the opening and closing force in the unit. See blowout preventer.

A dart-shaped drill pipe inside blowout preventer installed on top of the drill stem when the well is kicking through the drill stem. It is stabbed in open then closed against pressure.

Abbreviation: blowout preventer.

Abbreviation: blowout preventer equipment

See inside blowout preventer.

In drilling, to assemble the blowout preventer stack on the wellhead at the surface.

A ram device used to close the annular space around the polished rod or sucker rod in a pumping well.

The assembly of pumps, valves, lines, accumulators, and other items necessary to open and close the blowout preventer equipment.

The assembly of well-control equipment including preventers, spools, valves, and nipples connected to the top of the wellhead.

A device closed around the rods when the well may flow through the tubing while the rods are being pulled. It is a form of blowout preventer.

An integral part of a blowout preventer, which serves as the closing element on an open hole. Its ends do not fit around the drill pipe but seal against each other and shut off the space below completely. See ram

The joint of drill pipe that is used in hang-off operations so that no tool joint is opposite a set of preventer rams.

2. the pressure-sealing element of a stripper blowout preventer See stripper head.

A training procedure to determine that rig crews are completely familiar with correct operating practices to be followed in the use of blowout prevention equipment. A "dry run" of blowout preventative action.

An extension from the blowout preventer assembly used to direct control the flow of well fluids from the annulus to the choke.

The ratio between the pressure in the hole and the operating-piston pressure needed to close the rams of a blowout preventer.

Preventers installed on top of the well or drill string as a precautionary measure while running wirelines. The preventer packing will close around the wireline.

1. a large valve located on the Christmas tree and used to control the flow of oil and gas from a well. Also called master gate. 2. the blind or blank rams of a blowout preventer (obsolete).

The ratio between the pressure required to open the preventer and the well pressure under the rams.

A fitting placed in the blowout preventer stack to provide space between preventers for facilitating stripping operations, to permit attachment of choke and kill lines, and for localizing possible erosion by fluid flow to the spool instead of to the more expensive pieces of equipment.

A short length of pipe (a nipple) installed on top of the blowout preventer. The top end of the nipple is flared, or belled, to guide drill tools into the hole and usually has side connections for the fill line and mud return line.

The act of ensuring that a pipe ram preventer will not close on a drill pipe tool joint when the drill stem is stationary. A pup joint is made up in the drill string to lengthen it sufficiently.

The component in a blowout preventer that cuts, or shears, through drill pipe and forms a seal against well pressure. Shear rams are used in floating offshore drilling operations to provide a quick method of moving the rig away from the hole when there is no time to trip the drill stem out of the hole.

To take rams out of a blowout preventer and replace them with rams of a different size or type. When the size of a drill pipe is changed, the size of the pipe rams must be changed to ensure that they seal around the pipe when closed (unless variable-bore pipe rams are in use).

The valve on the choke and flow line that is nearest to the preventer assembly. Its purpose is to stop the flow through the choke and flow line.

One of several valves installed at the wellhead to prevent the escape of pressure either in the annular space between the casing and drill pipe or in open hole (i.e., hole with no drill pipe) during drilling completion operations. Blowout preventers on land rigs are located beneath the rig at the land's surface; on jackup or platform rigs, at the water's surface; and on floating offshore rigs, on the seafloor.

The closing and sealing component on a blowout preventer. One of three types--blind, pipe, or shear--may be installed in several preventers mounted in a stack on top of the wellbore. Blind rams, when closed, form a seal on a hole that has no drill pipe in it; pipe rams, when closed, seal around the pipe; shear rams cut through drill pipe and then form a seal.