Oil & Gas Glossary 1.0

The smaller of the side fittings on a bell nipple, used to fill the hole when drill pipe is being removed from the well.

To pump drilling fluid into the wellbore while the pipe is being withdrawn to ensure that the wellbore remains full of fluid even though the pipe is withdrawn. Filling the hole lessens the danger of a kick or of caving of the well or the wellbore.

A short length of pipe (a nipple) installed on top of the blowout preventer. The top end of the nipple is flared, or belled, to guide drill tools into the hole and usually has side connections for the fill line and mud return line.

To fill a wellbore up to the surface.

A formation fluid sampling device, actually run on conductor line rather than wireline, that also logs flow and shut-in pressure in rock near the borehole. A spring mechanism holds a pad firmly against the sidewall while a piston creates a vacuum in a test chamber. Formation fluids enter the tes5t chamber through a valve in the pad. A recorder logs the rate at which the test chamber is filled. Fluids may also be drawn to fill a sampling chamber. Wireline formation tests may be done any number of times during one tip in the hole, so they are very useful in formation testing.

Drilling in which the size of the hole is smaller than the conventional hole diameter for a given depth. This decrease in hole size enables the operator to run smaller casing, thereby lessening the cost of completion. See miniaturized completion.

1. a tool placed on a drill collar near the bit that is used, depending on where it is placed, either to maintain a particular hole angle or to change the angle by controlling the location of the contact point between the hole and the collars. See packed-hole assembly.

2. a hole of a diameter smaller than the main hole and drilled in the bottom of the main hole.

A device that is fastened to the outside of casing to remove mud cake from the wall of a hole to condition the hole for cementing. By rotating or moving the casing string up and down as it is being run into the hole, the scratcher, formed of stiff wire, removes the cake so that the cement can bond solidly to the formation.

A mechanical fluid-measuring device that measures by filling and emptying chambers of a specific volume. The displacement of a fixed volume of fluid may be accomplished by the action of reciprocating or oscillating pistons, rotating vanes or buckets, rotating disks, or tanks or other vessels that automatically fill and empty. Also called a volume meter or volumeter.

A small mud tank with a capacity of 10 to 15 barrels, usually with 1-barrel or H-barrel divisions, used to ascertain the amount of mud necessary to keep the wellbore full with the exact amount of mud that is displaced by drill pipe. When the bit comes out of the hole, a volume of mud equal to that which the drill pipe occupied while in the hole must be pumped into the hole to replace the pipe. When the bit goes back in the hole, the drill pipe displaces a certain amount of mud, and a trip tank can be used again to keep track of this volume.

A cycle, or down the hole and back, is the time required for the pump to move the drilling fluid in he hole. The cycle in minutes equals the barrels of mud in the hole divided by barrels per minute.

A bell-shaped hole dug beneath a pipeline to provide room for use of tools.

A bottomhole assembly consisting of stabilizers and large-diameter drill collars arranged in a particular configuration to maintain drift angle and direction of a hole.

To pump a designated quantity of a substance (such as acid or cement) into a specific interval in the well. For example, 10 barrels of diesel oil may be spotted around an area in the hole in which drill collars are stuck against the wall of the hole in an effort to free the collars.

In pipeline construction, the hole drilled as the first step of a directionally drilled river crossing. It establishes a pathway for the pipeline.

The component in a blowout preventer that cuts, or shears, through drill pipe and forms a seal against well pressure. Shear rams are used in floating offshore drilling operations to provide a quick method of moving the rig away from the hole when there is no time to trip the drill stem out of the hole.

A fluid moving as a unit in which all shear stress occurs at the pipe wall and hole wall. The stream thus assumes the shape of several telescopic layers of fluid with lowest velocities near the pipe and hole walls and the fastest in the middle.

A drilling method in which the hole is drilled by dropping a sharply pointed bit on bottom. The bit is attached to a cable, and the cable is repeatedly dropped as the hole is drilled.

A method of preparing a well for production in which no production casing or liner is set opposite the producing formation. Reservoir fluids flow unrestricted into the open wellbore. An open-hole completion has limited use in rather special situations. Also called a barefoot completion.

Drill pipe, drill collars, casing, or tubing that has inadvertently become immovable in the hole. Sticking may occur when drilling is in progress, when casing is being run in the hole, or when the drill pipe is being hoisted.

A process used to repair a hole in the casing by pumping cement down tubing or drill pipe. First, the casinghead, or bradenhead, is closed to prevent fluids from moving up the casing. Then the rig's pumps are started. Pump pressure moves the cement out of the tubing or pipe and, since the top of the casing is closed, the cement goes into the hole in the casing. The tubing or pipe is pulled from the well and the cement allowed to harden. The hardened cement seals the hole in the casing. Although the term "bradenhead squeezing" is still used, the term "bradenhead" is obsolete. See annular space, casinghead, squeeze.

A borehole; the hole drilled by the bit. A wellbore may have casing in it or it may be open (uncased); or part of it may be cased, and part of it may be open. Also called a borehole or hole.

One of several valves installed at the wellhead to prevent the escape of pressure either in the annular space between the casing and drill pipe or in open hole (i.e., hole with no drill pipe) during drilling completion operations. Blowout preventers on land rigs are located beneath the rig at the land's surface; on jackup or platform rigs, at the water's surface; and on floating offshore rigs, on the seafloor.

A logging method that records rift angle, or deflection from the vertical, and direction of the drift. A single-shot directional-survey instrument makes a single photograph of a compass reading of the draft direction and the number of degrees the hole is off vertical. A multishot survey instrument obtains numerous readings in the hole as the device is pulled out of the well. See directional drilling.

N: a collar or coupling of tool steel, threaded internally, that can be used to retrieve pipe from the well on fishing jobs; the female counterpart of a taper tap. The die collar is made up on the drill pipe and lowered into the hole until it contacts the lost pipe. If the lost pipe is stuck so that it cannot rotate, rotation of the die collar on top of the pipe cuts threads on the outside of the pipe, providing a firm attachment. The pipe is then retrieved from the hole. Compare taper tap. It is not often used because it is difficult to release it from the fish should it become necessary.

Generally, the first string of casing in a well. It may be lowered into a hole drilled into the formations near the surface and cemented in place; it may be driven into the ground by a special pile driver (in such cases, it is sometimes called drive pipe); or it may be jetted into place in offshore locations. Its purpose is to prevent the soft formations near the surface from caving in and to conduct drilling mud from the bottom of the hole to the surface when drilling starts. Also called conductor pipe.

Generally, the first string of casing in a well. It may be lowered into a hole drilled into the formations near the surface and cemented in place; or it may be driven into the ground by a special pile drive (in such cases, it is sometimes called drive pipe); or it may be jetted into place in offshore locations. Its purpose is to prevent the soft formations near the surface from caving in and to conduct drilling mud from the bottom of the hole to the surface when drilling starts. Also called conductor pipe.

To release pipe that is stuck in the hole by running washover pipe. The washover pipe must have an outside diameter small enough to fit into the borehole but an inside diameter large enough to fit over the outside diameter of the stuck pipe. A rotary shoe, which cuts away the formation, mud, or whatever is sticking the pipe, is made up on the bottom joint of the washover pipe, and the assembly is lowered into the hole. Rotation of the assembly frees the stuck pipe. Several washovers may have to be made if the stuck portion is very long.

A device that prevents leakage along a piston, rod, propeller shaft, or other moving part that passes through a hole in a cylinder or vessel. It consists of a box or chamber made by enlarging the hole and a gland containing compressed packing. On a well being artificially lifted by means of a sucker rod pump, the polished rod operates through a stuffing box, preventing escape of oil and diverting it into a side outlet to which is connected the flow line leading to the oil and gas separator or to the field storage tank. For a bottomhole pressure test, the wireline goes through a stuffing box and lubricator, allowing the gauge to be raised and lowered against well pressure. The lubricator provides a pressure-tight grease seal in the stuffing box.

Abbreviation: run-in-hole.

To run casing or pipe.

A wellbore in which casing has been run.

Abbreviation: pull-out-of-hole

Uncased portion of a well.

To begin drilling; to start the hole.

A wellbore or formation known to contain hydrogen sulfide gas.

2. of a hole, having no drill pipe or tubing suspended in it.

A hole made by drilling or boring; a wellbore.

A hole dug, usually before drilling of a well, to allow working space for the casinghead equipment.

1. to seal the hole against formation fluids by allowing the buildup of wall cake.

To pass (as a rope) through a hole or opening in a block or similar device.

The depth in the hole at which the tubing, casing, or drill pipe is stuck.

To lower the drill stem, tubing, casing, or sucker rods in to the wellbore.

2. to force a wireline tool or tubing down the hole by using a reciprocating motion.

To bore a hole in the earth, usually to find and remove subsurface formation fluids such as oil and gas.

2. a hole or opening in a line or vessel into which a gauge or valve may be inserted and screwed tight.

A threaded nipple with a rounded, closed end used to stop up a hole or close off the end of a line.

Hydrocarbons which are in the gaseous state under reservoir conditions but which become liquid either in passage up the hole or at the surface.

An exploratory or development well found to be incapable of producing either oil or gas in sufficient quantities to justify completion as an oil or gas well.

2. a tool place in the hole to retain cement or other material; it may later be removed, drilled out, or left permanently.

A phenomenon that sometimes occurs when a well blows out. Rocks, sand, clay, and other debris clog the hole and stop the blowout.

A device used to enlarge the size of an existing borehole, having teeth arranged on its outside circumference to cut the formation as it rotates.

1. to explode nitroglycerine or other high explosives in a hole to shatter the rock and increase the flow of oil, now largely replaced by formation fracturing.

Any of a variety of drilling bits that have no moving parts. As they are rotated on bottom, elements of the bit make hole by being pressed into the formation and being dragged across it. See fishtail bit.

A wellbore that has been unintentionally drilled in a direction other than vertical. It usually occurs where there is a section of alternating hard and soft strata steeply inclined from the horizontal.

A vertical pipe rising along the side of the derrick or mast, which joins the discharge line leading from the mud pump to the rotary hose and through which mud is pumped going into the hole.

The crew member who handles the upper end of the drill string as it is being hoisted out of or lowered into the hole. He is also responsible for the circulating machinery and the conditioning of the drilling fluid.

The depth in the hole at which the drill stem, tubing, or casing is stuck.

Any object or device that blocks a hole or passageway (such as a cement plug in a borehole).

To prepare the drilling rig for making hole; to install tools and machinery before drilling is started.

A hole in the side of a tank through which a man can enter the tank, also the cleanout plate.

2. to stand pipe on the derrick floor when pulling it out of the hole.

2. difference between the annular velocity of the fluid and the rate at which a cutting is removed from the hole.

To place cement plugs into a dry hole and abandon it.

An integral part of a blowout preventer, which serves as the closing element on an open hole. Its ends do not fit around the drill pipe but seal against each other and shut off the space below completely. See ram

A tool used in drilling to smooth the wall of a well, enlarge the hole to the specified size, help stabilize the bit, straighten the wellbore if kinks or doglegs are encountered, and rill directionally. See ream.

To use a whipstock, turbodrill, or other mud motor to drill around broken drill pipe or casing that has become lodged permanently in the hole.

A device used with slips to prevent tubing from falling into the hole when a joint of pipe is being unscrewed and racked.

A plug in the flow line at the well head which has a small hole drilled through it through which oil flows, and which keeps a well from flowing at too high a rate.

Clamps that grip a stand of casing, tubing, drill pipe, or sucker rods so that the stand can be raised or lowered into the hole.

1. a hole in the rig floor, 30 to 35 feet (9 to 11 meters) deep, which is lined with casing that projects above the floor and into which the kelly and swivel are placed when hoisting operations are in progress.

The partial or complete collapse of the walls of a hole resulting from internal pressures due primarily to swelling from hydration or formation gas pressures. See caving.

(slang) to cave in; to fail. After a violent blowout, the force of the fluids escaping from the wellbore sometimes blows a large hole in the ground. In this case, the well is said to have cratered. Equipment craters when it falls.

An assembly of tools made up on drill pipe that is lowered into the hole to retrieve lost or stuck equipment. Also call a fish assembly.

A fishing tool containing metal-cutting knives that is lowered into the hole and over the outside of a length of pipe to cut it. The severed part of the pipe can then be brought to the surface.

See open-hole completion

1. to move the drill stem up and down in the hole over a short distance without rotation. Careless execution of this operation creates pressure surges that can cause a formation to break down, resulting in lost circulation.

1. a passageway through jet bits that causes the drilling fluid to be ejected from the bit at high velocity. The jet of mud clears the bottom of the hole. Nozzles come in different sizes that can be interchanged on the bit to adjust the velocity with which the mud exits the bit.

To install a pump or pumping unit, sucker rods, and bottom-hole pump.

A device secured around the casing at the regular intervals to center it in the hole. Casing that is centralized allows a more uniform cement sheath to form around the pipe.

The smooth, uninterrupted circulation of drilling fluid down the drill stem, out the bit, up the annular space between the pipe and the hole, and back to the surface. Compare reverse circulation.

A hole made in the casing, cement, and formation through which formation fluids enter a wellbore. Usually several perforations are made at a time.

The ratio between the pressure in the hole and the operating-piston pressure needed to close the rams of a blowout preventer.

A hole drilled in the earth for purpose of (1) finding or producing crude oil or natural gas; or (2) providing services related to the production of crude oil or natural gas.

1. a rubber disk surrounding drill pipe or tubing that removes mud as the pipe is brought out of the hole.

A small attachment on the rod-transfer equipment that picks up the rods after they are unscrewed from the string and then transfers them to the rod hanger, or reverses the procedure when going into the hole. See rod-transfer equipment.

The action of pull out and subsequently running back into the hole a string of drill pipe or tubing. Making a round trip is also called tripping.

A type of packer used for open-hole work, with inflatable packing elements

Steel pipe placed in an oil or gas well as drilling progresses to prevent the wall of the hole from caving in during drilling, to prevent seepage of fluids, and to provide a means of extracting petroleum if the well is productive.

A walled round hole or well in the hull of a drill ship (usually in the center) through which the drilling assembly and other assemblies pass while a well is being drilled, completed, or abandoned from the drill ship.

The cementing operation that takes place immediately after the casing has been run into the hole. It provides a protective sheath around the casing, segregates the producing formation, and prevents the undesirable migration of fluids.

The small amount of additional mud weight carried over that needed to balance formation pressure to overcome the pressure-reduction effects caused by swabbing when a trip out of the hole is made.

A sudden, usually short-duration, increase in pressure. When pipe or casing is run into a hole too rapidly, an increase in the hydrostatic pressure results, which may be great enough to create lost circulation

A method of well completion in which a slotted or perforated liner, often wire-wrapped, is placed in the well and surrounded by gravel. If open hole, the well is sometimes enlarged by underreaming at the point where the gravel is packed. The mass of gravel excludes sand from the wellbore but allows continued production.

A trough or pipe that is placed between the surface connections at the wellbore and the shale shaker and through which drilling mud flows upon its return to the surface from the hole. Also called flow line.

To pull the drill stem out of the wellbore to change the bit, to change from a core barrel to the bit, to run electric logs, to prepare for a drill stem test, to run casing, and so on. Also called trip out.

A blowout preventer that uses rams to seal off pressure on a hole that is with or without pipe. Also called a ram preventer.

A preventer having a unit of packing material whose closure depends on well pressure coming from below. It is used primarily to strip pipe through the hole or allow pipe to be moved with pressure on the annulus.

Trade name for a downhole motor driven by drilling fluid that imparts rotary motion to a drilling bit connected to the tool, thus eliminating the need to turn the entire drill stem to make hole. Used in straight and directional drilling.

The recording of information derived from examination and analysis of formation cuttings made by the bit and of mud circulated out of the hole. A portion of the mud is diverted through a gas-detecting device. Cuttings brought up by the mud are examined under ultraviolet light to detect the presence of oil or gas. Mud logging is often carried out in a portable laboratory set up at the well.

The string of casing set in a well after the surface casing but before production casing is set. Keeps hole from caving and seals off troublesome formations. Also called protection casing.

A drilling method in which a hole is drilled by a rotating bit to which a downward force is applied. The bit is fastened to and rotated by the drill stem, which also provides a passageway through which the drilling fluid is circulated. Additional joints of drill pipe are added as drilling progresses.

A fishing tool that is attached to tubing or drill pipe and lowered over the outside wall of pipe or sucker rods lost or stuck in the wellbore. A friction device in the overshot, usually either a basket or as spiral grapple, firmly grips the pipe, allowing the fish to be pulled from the hole.

A special device that, when fitted in to the master bushing, transmits torque to the kelly and simultaneously permits vertical movement of the kelly to make hole. It may be shaped to fit the rotary opening or have pins for transmitting torque. Also called

The mud tank adjacent to the shake shaker, usually the first tank in to which mud flows after returning from the hole. Also called a shaker pit.

Two packers separated by a spacer of variable length. A straddle packer may be used to isolate sections of open hole to be treated or tested or to isolate certain areas of perforated casing from the rest of the perforated section.

A measure of the density of a drilling fluid expressed as pounds per gallon, pounds per cubic foot, or kilograms per cubic meter. Mud weight is directly related to the amount of pressure the column of drilling mud exerts at the bottom of the hole.

The derrickman's working platform. As pipe of tubing is run into or out of the hole, the derrickman must handle the top end of the pipe, which may be as high as 90 feet (27 m) in the derrick or mast. The monkeyboard provide a small platform to raise him to the proper height for handling the top of the pipe.

Departure of the wellbore from the vertical, measured by the horizontal distance from the rotary table to the target. The amount of deviation is a function of the drift angle and hole depth. The term is sometimes used to indicate the angle from which a bit has deviated from the vertical during drilling. See drift angle.

A water-base mud in which water is the continuous phase and oil is the dispersed phase. The oil is spread out, or dispersed, in the water in small droplets, which are tightly emulsified so that they do not settle out. Because of its lubricating abilities, an oil-emulsion mud increases the drilling rate and ensures better hole conditions than other muds. Compare oil mud.

1. to place pipe withdrawn from the hole on a pipe rack

A short cylindrical device installed in the drill stem between the bottom-most drill collar and a downhole motor. Its purpose is to deflect the downhole motor off vertical to drill a directional hole. See drill stem.

The force that a fluid (liquid or gas) exerts uniformly in all directions within a vessel, pipe, hole in the ground, and so forth, such as that exerted against the inner wall of a tank or that exerted on the bottom of the wellbore by a fluid. Pressure is expressed in terms of force exerted per unit of area, as pounds per square inch, or in kilopascals.

A device used in fishing for drill pipe. If the upper end of the lost pipe is leaning against the side of the wellbore, the wall hook centers it in the hole so that it may be recovered with an overshot, which is run on the fishing string and attached to the wall hook.

A block with lead or another relatively soft material on its bottom. It is made up of drill pipe or tubing at the surface, run into a well, and set down on the object that has been lost in the well. The block is retrieved and the impression is examined. The impression is a mirror image of the top of the fish and indicates the fish's position in the hole, i.e., whether it is centered or off to one side. From this information, the correct fishing tool can be selected.

To measure drill pipe or tubing as it is pulled out of the hole, usually to determine the depth of the well or the depth to which the pipe or tubing was run.

A cast-iron or magnesium drillable tool consisting of a packing assembly and a back-pressure valve. It is used to close off the annular space between tubing or drill pipe and casing to allow the placement of cement or fluid through the tubing or drill pipe at any predetermined point behind the casing or liner, around the shoe, or into the open hole around the shoe.

A means of cementing casing in a well so that the casing may, if necessary, be retrieved with minimum difficulty. A special mud, usually an oil mud, is placed in the well ahead of the cement after the casing has been set. Non-solidifying mud is used so that it does not bind or stick to the casing in the hole in the area above the cement. Since the mud does not gel for a long time, the casing can be cut above the cemented section and retrieved. Casing packs are used in wells of doubtful or limited production to permit reuse of valuable lengths of casing.

A downhole tool with rough, sharp, extremely hard cutting surfaces for removing metal by grinding or cutting. Mills are run on drill pipe or tubing to grind up debris in the hole, remove stuck portions of drill stem or sections of casing for sidetracking, and ream out tight spots in the casing. They are also called junk mills, reaming mills, and so forth, depending on what use they have.

The pressure at the bottom of a well.

To create holes in casing and cement set through a productive formation. A common method of completing a well is to set casing through the oil-bearing formation and cement it. A perforating gun is then lowered into the hole and fired to detonate high-powered jets or shoot steel projectiles (bullets) through the casing and cement and into the pay zone. The formation fluids flow out of the reservoir through the perforations and into the wellbore. See perforating gun.

A special mill that has a heavy tubular extension below it called a pilot or stinger. The pilot, smaller in diameter than the mill, is designed to go inside drill pipe or tubing that is lost in the hole. It guides the mill to the top of the pipe and centers it, thus preventing the mill from bypassing the pipe. Also called a piloted mill.

A fishing tool used to retrieve pipe lost in a well. The spear is lowered down the hole and into the lost pipe. When weight, torque, or both are applied to the string to which the spear is attached, the slips in the spear expand and tightly grip the inside of the wall of the lost pipe. Then the string, spear, and lost pipe are pulled to the surface.

A coring technique in which core samples are obtained from the hole wall in a zone that has already been drilled. A hollow bullet is fired into the formation wall to capture the core and then retrieved on a flexible steel cable. Core samples of this type usually range from 3/4 to 1-3/16 inches (20 to 30 millimeters) in diameter and from 3/4 to 4 inches (20 to 100 millimeters) in length. This method is especially useful in soft-rock areas.

The course of drilling fluid downward through the annulus and upward through the drill stem, in contrast to normal circulation in which the course is downward through the drill stem and upward through the annulus. Seldom used in open hole, but frequently used in workover operations. Also referred to as "circulating the short way," since returns from bottom can be obtained more quickly than in normal circulation.

A workover performed with a continuous steel tube, normally 3/4 inch to 1 inch outside diameter, which is run into the well in one piece inside the normal tubing. Lengths of the tubing up to 16,000 feet are stored on the surface on a reel in a manner similar to that used for wireline. The unit is rigged up over the wellhead. The tubing is injected through a control head that seals off the tubing and makes a pressure-tight connection. A unique feature of the unit is that it allows continuous circulation while it is being lowered into the hole.

A short, threaded piece of pipe used to adapt parts of the drilling string that cannot otherwise be screwed together because of differences in thread size or design. A sub (i.e., a substitute) may also perform a special function. Lifting subs are used with drill collars to provide a shoulder to fit the drill pipe elevators; a kelly saver sub is placed between the drill pipe and the kelly to prevent excessive thread wear of the kelly and drill pipe threads, a bent sub is used when drilling a directional hole.

An accessory to a fishing tool, placed above it. if the tool cannot be disengaged from the fish, the safety joint permits easy disengagement of the string of pipe above the safety joint. Thus, part of the safety joint and the tool attached to the fish remain in the hole and become part of the fish.

The closing and sealing component on a blowout preventer. One of three types--blind, pipe, or shear--may be installed in several preventers mounted in a stack on top of the wellbore. Blind rams, when closed, form a seal on a hole that has no drill pipe in it; pipe rams, when closed, seal around the pipe; shear rams cut through drill pipe and then form a seal.

A device made up in the drill stem above the mill to collect bits of junk ground away during a milling operation. During milling, drilling mud under high pressure forces bits of junk up the narrow space between the boot sub and the hole wall. When the junk reaches the wider annulus above the boot sub and pressure drops slightly, the junk falls into the boot sub. A boot sub also can be run above the bit during routine drilling to collect small pieces of junk that may damage the bit or interfere with its operation.